115 lines
2.6 KiB
Plaintext
115 lines
2.6 KiB
Plaintext
# For more options and information see
|
|
# http://rpf.io/configtxt
|
|
# Some settings may impact device functionality. See link above for details
|
|
|
|
# uncomment if you get no picture on HDMI for a default "safe" mode
|
|
#hdmi_safe=1
|
|
|
|
# uncomment this if your display has a black border of unused pixels visible
|
|
# and your display can output without overscan
|
|
#disable_overscan=1
|
|
|
|
# uncomment the following to adjust overscan. Use positive numbers if console
|
|
# goes off screen, and negative if there is too much border
|
|
|
|
# uncomment to force a console size. By default it will be display's size minus
|
|
# overscan.
|
|
#framebuffer_width=1280
|
|
#framebuffer_height=720
|
|
|
|
# uncomment if hdmi display is not detected and composite is being output
|
|
#hdmi_force_hotplug=1
|
|
|
|
# uncomment to force a specific HDMI mode (this will force VGA)
|
|
#hdmi_group=1
|
|
#hdmi_mode=1
|
|
|
|
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
|
|
# DMT (computer monitor) modes
|
|
#hdmi_drive=2
|
|
|
|
# uncomment to increase signal to HDMI, if you have interference, blanking, or
|
|
# no display
|
|
#config_hdmi_boost=4
|
|
|
|
# uncomment for composite PAL
|
|
#sdtv_mode=2
|
|
|
|
#uncomment to overclock the arm. 700 MHz is the default.
|
|
#arm_freq=800
|
|
|
|
# Uncomment some or all of these to enable the optional hardware interfaces
|
|
#dtparam=i2s=on
|
|
#dtparam=spi=on
|
|
|
|
# Uncomment this to enable infrared communication.
|
|
#dtoverlay=gpio-ir,gpio_pin=17
|
|
#dtoverlay=gpio-ir-tx,gpio_pin=18
|
|
|
|
# Additional overlays and parameters are documented /boot/overlays/README
|
|
|
|
# Enable audio (loads snd_bcm2835)
|
|
dtparam=audio=on
|
|
|
|
[pi4]
|
|
# Enable DRM VC4 V3D driver on top of the dispmanx display stack
|
|
dtoverlay=vc4-fkms-v3d
|
|
max_framebuffers=2
|
|
|
|
[all]
|
|
dtoverlay=vc4-fkms-v3d
|
|
|
|
# Custom power settings
|
|
max_usb_current=1
|
|
|
|
# Disable the PWR LED.
|
|
# dtparam=pwr_led_trigger=none
|
|
# dtparam=pwr_led_activelow=off
|
|
|
|
# Disable Rainbow splash
|
|
disable_splash=1
|
|
|
|
# GPU Mem
|
|
gpu_mem=256
|
|
|
|
# Overscan fix
|
|
overscan_scale=1
|
|
|
|
# Enable watchdog
|
|
dtparam=watchdog=on
|
|
|
|
# Boot time improvements
|
|
boot_delay=0
|
|
initial_turbo=30
|
|
start_cd=1
|
|
#dtoverlay=sdtweak,overclock_50=100
|
|
|
|
# Bluetooth
|
|
dtoverlay=pi3-disable-bt
|
|
|
|
# VGA666
|
|
dtoverlay=vga666
|
|
enable_dpi_lcd=1
|
|
display_default_lcd=1
|
|
dpi_group=2
|
|
dpi_mode=87
|
|
|
|
# test
|
|
dpi_timings=400 0 16 32 48 234 0 9 3 17 0 0 0 60 1 8000000 1 # ok
|
|
#dpi_timings=848 0 24 80 104 480 0 3 10 7 0 0 0 60 0 31500000 1
|
|
#dpi_timings=400 0 16 96 48 234 0 11 2 31 0 0 0 60 0 12175000 1
|
|
# 640x480x50Hz
|
|
#dpi_timings=640 0 16 96 48 480 0 11 2 31 0 0 0 60 0 25175000 1
|
|
|
|
#dpi_timings=320 0 16 96 48 240 0 11 2 31 0 0 0 60 0 12587500 6
|
|
|
|
# overscan_left=16
|
|
# overscan_right=0
|
|
# overscan_top=0
|
|
# overscan_bottom=0
|
|
|
|
|
|
# I2C Bus
|
|
dtparam=i2c_arm=on
|
|
dtparam=spi=off
|