working in progress...

Raspberry/config.txt

@@ -0,0 +1,114 @@
+# For more options and information see
+# http://rpf.io/configtxt
+# Some settings may impact device functionality. See link above for details
+
+# uncomment if you get no picture on HDMI for a default "safe" mode
+#hdmi_safe=1
+
+# uncomment this if your display has a black border of unused pixels visible
+# and your display can output without overscan
+#disable_overscan=1
+
+# uncomment the following to adjust overscan. Use positive numbers if console
+# goes off screen, and negative if there is too much border
+
+# uncomment to force a console size. By default it will be display's size minus
+# overscan.
+#framebuffer_width=1280
+#framebuffer_height=720
+
+# uncomment if hdmi display is not detected and composite is being output
+#hdmi_force_hotplug=1
+
+# uncomment to force a specific HDMI mode (this will force VGA)
+#hdmi_group=1
+#hdmi_mode=1
+
+# uncomment to force a HDMI mode rather than DVI. This can make audio work in
+# DMT (computer monitor) modes
+#hdmi_drive=2
+
+# uncomment to increase signal to HDMI, if you have interference, blanking, or
+# no display
+#config_hdmi_boost=4
+
+# uncomment for composite PAL
+#sdtv_mode=2
+
+#uncomment to overclock the arm. 700 MHz is the default.
+#arm_freq=800
+
+# Uncomment some or all of these to enable the optional hardware interfaces
+#dtparam=i2s=on
+#dtparam=spi=on
+
+# Uncomment this to enable infrared communication.
+#dtoverlay=gpio-ir,gpio_pin=17
+#dtoverlay=gpio-ir-tx,gpio_pin=18
+
+# Additional overlays and parameters are documented /boot/overlays/README
+
+# Enable audio (loads snd_bcm2835)
+dtparam=audio=on
+
+[pi4]
+# Enable DRM VC4 V3D driver on top of the dispmanx display stack
+dtoverlay=vc4-fkms-v3d
+max_framebuffers=2
+
+[all]
+dtoverlay=vc4-fkms-v3d
+
+# Custom power settings
+max_usb_current=1
+
+# Disable the PWR LED.
+# dtparam=pwr_led_trigger=none
+# dtparam=pwr_led_activelow=off
+
+# Disable Rainbow splash
+disable_splash=1
+
+# GPU Mem
+gpu_mem=256
+
+# Overscan fix
+overscan_scale=1
+
+# Enable watchdog
+dtparam=watchdog=on
+
+# Boot time improvements
+boot_delay=0
+initial_turbo=30
+start_cd=1
+#dtoverlay=sdtweak,overclock_50=100
+
+# Bluetooth
+dtoverlay=pi3-disable-bt
+
+# VGA666
+dtoverlay=vga666
+enable_dpi_lcd=1
+display_default_lcd=1
+dpi_group=2
+dpi_mode=87
+
+# test
+dpi_timings=400 0 16 32 48 234 0 9 3 17 0 0 0 60 1 8000000 1 # ok
+#dpi_timings=848 0 24 80 104 480 0 3 10 7 0 0 0 60 0 31500000 1
+#dpi_timings=400 0 16 96 48 234 0 11 2 31 0 0 0 60 0 12175000 1
+# 640x480x50Hz
+#dpi_timings=640 0 16 96 48 480 0 11 2 31 0 0 0 60 0 25175000 1
+
+#dpi_timings=320 0 16 96 48 240 0 11 2 31 0 0 0 60 0 12587500 6
+
+# overscan_left=16
+# overscan_right=0
+# overscan_top=0
+# overscan_bottom=0
+
+
+# I2C Bus
+dtparam=i2c_arm=on
+dtparam=spi=off

Raspberry/crankshaft_env.sh

@@ -0,0 +1,212 @@
+### Hardware ###
+# The hardware pins can be completly disabled with the global flag.
+
+# Global Flag (enables / disables gpio usage excluding device connected
+# trigger gpio and ignition based shutdown!)
+ENABLE_GPIO=0
+
+# Possible used gpio's by hifiberry dac's depending on model:
+# For more info visit the hifiberry homepage! To prevent from bugs don't use them!
+#
+# GPIO 4,5,6,16,18,19,20,21,27,28,29,30,31
+
+# Generally used GPIO's
+# Used for HAT modules - Never use it!
+# GPIO 27,28
+
+# GPIO Setup
+DEV_PIN=0
+INVERT_PIN=0
+X11_PIN=0
+
+# Device connected gpio (device connected 1 / else 0)
+# Note: this gpio depends NOT on ENABLE_GPIO!!!
+# To disable set to 0
+ANDROID_PIN=0
+
+# GPIO Trigger for Rearcam
+# GPIO wich triggers enabling Rearcam Mode of RPICam
+# To disable set to 0
+REARCAM_PIN=0
+
+# GPIO Trigger for Day/Night
+# GPIO wich triggers Day (open gpio)/Night (closed to gnd) of GUI
+# To disable set to 0
+# If enabled it overrides lightsensor!
+DAYNIGHT_PIN=0
+
+### Maintenance / Initial Setup ###
+# Start Crankshaft in dev mode to get network, shell and ssh access
+# openauto won't be started automatically
+DEV_MODE=1
+# Start openauto in dev mode if enabled
+DEV_MODE_APP=0
+
+### Debugging ###
+# Start Crankshaft in debug mode to get network, shell and ssh access
+# System will do a normal start in ro mode
+DEBUG_MODE=1
+
+### OpenAuto ###
+# Start OpenAuto in X11 or EGL
+# By default, EGL, but if you can't get it to work, do X11
+START_X11=1
+
+### Screen ###
+# Brightness related stuff
+# brightness file (default for rpi display: /sys/class/backlight/rpi_backlight/brightness)
+BRIGHTNESS_FILE=/sys/class/backlight/rpi_backlight/brightness
+
+# brightness values
+BR_MIN=30
+BR_MAX=255
+BR_STEP=25
+BR_DAY=83
+BR_NIGHT=30
+
+# Custom brightness control
+# Note: this command is called after every brightness change - can slow down for example the brightness
+# slider depending on execution speed - the process is called with "&" so call is not waiting for exit!
+# Sample call which will be executed on request: "CUSTOM_BRIGHTNESS_COMMAND brightnessvalue &"
+#
+# Note: To allow backup and restore your command must be located on /boot/crankshaft/custom/
+# otherwise it will not be transfered during updates!
+#
+# To disable leave empty
+CUSTOM_BRIGHTNESS_COMMAND=
+
+# Flip the screen 180°
+FLIP_SCREEN=0
+
+### Audio ###
+# If stored vol is lower than this set to this value
+STARTUP_VOL_MIN=30
+# If stored vol is greater than this limit to this value
+STARTUP_VOL_MAX=100
+
+###  Power Mgmt Related Stuff ###
+# Timeout display after disconnect or after boot without connected device
+DISCONNECTION_SCREEN_POWEROFF_SECS=120
+# Disable Timer
+DISCONNECTION_SCREEN_POWEROFF_DISABLE=0
+# Use screensaver (bg+clock) instead of display off
+SCREEN_POWEROFF_OVERRIDE=0
+
+# Timeout shutdown after disconnect or after boot without connected device
+#
+# Note: on first boot timeout is set to 300 seconds - after first start
+# this value is used
+DISCONNECTION_POWEROFF_MINS=60
+# Disable Timer
+DISCONNECTION_POWEROFF_DISABLE=0
+
+### Wifi Setup ###
+# Your country code like EN,DE,FR,UK etc.
+WIFI_COUNTRY=FR
+
+# Wifi client mode (use this entry for home/work wifi - not for phone's hotspot)
+# If your SSID or password contains special chars or spaces make sure using quotation marks ="SSID" / ="password"
+WIFI_SSID="POCOX3"
+WIFI_PSK="123456789"
+# Optinal 2nd config to access to phone's hotspot
+# Note: if second config is configured system will use first connectable wifi during boot
+WIFI2_SSID="sample"
+WIFI2_PSK="sample"
+
+# Force recreate wpa_supplicant.conf during boot after wifi credentials have changed by user (default 0 | update 1)
+WIFI_UPDATE_CONFIG=0
+
+# Hotspot (if enabled the wifi client is disabled and a hotspot is opened)
+# Hotspot has now a default password (1234567890) -> changeable in /etc/hostapd/hostapd.conf if really needed!
+ENABLE_HOTSPOT=0
+
+### RPi Camera Module ###
+# Overlay settings
+RPICAM_X=100
+RPICAM_Y=52
+RPICAM_WIDTH=590
+RPICAM_HEIGTH=366
+RPICAM_HFLIP=0
+RPICAM_VFLIP=0
+RPICAM_ROTATION=0
+RPICAM_FPS=24
+RPICAM_AWB=auto
+RPICAM_EXP=auto
+### Dashcam realted stuff ###
+# Time for a recording segment
+RPICAM_LOOPTIME=300
+# Max archived recording files / oldest will be removed if newer is created
+RPICAM_LOOPCOUNT=3
+# Start recording on system startup (0|1)
+RPICAM_AUTORECORDING=0
+# Res: 720/1080 (default:720)
+RPICAM_RESOLUTION=720
+# Don't manually edit this values (use gui)
+RPICAM_ZOOM=0
+RPICAM_YCORRECTION=0
+
+# USB Rearcam ###
+# Use usb cam instead of rpi cam module for rearcam
+USBCAM_USE=0
+# Overlay settings
+USBCAM_ROTATION=0
+USBCAM_HFLIP=0
+USBCAM_VFLIP=0
+# Ignore all and use this custom params
+# Only for special setups
+USBCAM_CUSTOM_PARAMS=
+
+# RTC Related Settings ###
+# Enables day/night switch by rtc - don't change manually!
+# Use command 'crankshaft rtc xxx' in shell!
+RTC_DAYNIGHT=0
+
+# Day / Night (only working with rtc enabled) - don't change manually!
+# Use command 'crankshaft timers daynight xx xx' in shell!
+RTC_DAY_START=8
+RTC_NIGHT_START=18
+
+# Ignition Based Shutdown
+# This pin must be low to keep system running. If high for > IGNITION-DELAY (seconds)
+# system will do a shutdown
+# Note: this gpio depends NOT on ENABLE_GPIO!!!
+# To disable set to 0
+IGNITION_PIN=0
+# Time to wait until shutting down (seconds)
+IGNITION_DELAY=60
+
+# Enable experimental bluetooth stuff
+# don't use - only prepared for further releases!
+ENABLE_BLUETOOTH=0
+# Allow to autopair devices
+ENABLE_PAIRABLE=0
+# Use external adapter not builtin
+EXTERNAL_BLUETOOTH=0
+
+# System updates
+ALLOW_USB_FLASH=1
+
+# LightSensor
+LIGHTSENSOR_TYPE='TSL2561' # Allowed Values TSL2561 TSL2591
+# the address of TSL2561/TSL2591 can be
+# 0x29, 0x39 or 0x49
+TSL_I2C_BUS=1
+TSL_ADDR=0x29
+
+# Auto brightness control based on tsl2561 light sensor
+# Check interval sensor 5,10,15,20,25,30
+TSL2561_CHECK_INTERVAL=10
+# Switch to night on this level or lower (0 = disabled / 1-5)
+TSL2561_DAYNIGHT_ON_STEP=2
+# Switch levels for brightness sensor in lux
+LUX_LEVEL_1=5
+LUX_LEVEL_2=20
+LUX_LEVEL_3=100
+LUX_LEVEL_4=200
+LUX_LEVEL_5=500
+# Set this display brightness by switch levels
+DISP_BRIGHTNESS_1=30
+DISP_BRIGHTNESS_2=90
+DISP_BRIGHTNESS_3=150
+DISP_BRIGHTNESS_4=210
+DISP_BRIGHTNESS_5=255

Raspberry/debugOscillo/Notes.md

@@ -10,6 +10,8 @@ Visible but only halph of the screen...
 - 320x240 60Hz : 'dpi_timings=320 1 12 32 44 240 1 6 10 6 0 0 0 60 0 6400000 1`
 Not working
 
+## Resolution:
+- 400x234
 
 
 ## Syntax: 

Raspberry/timingLineGenerate.py

@@ -33,22 +33,22 @@ print("DPI Command : ")
 # HDMI_ASPECT_64_27 = 8
 
 p = [0] *17
-p[0] =  416   # h_active_pixels = horizontal pixels (width)
+p[0] =  848   # h_active_pixels = horizontal pixels (width)
 p[1] =  0   # h_sync_polarity = invert hsync polarity
-p[2] =  12   # h_front_porch   = horizontal forward padding from DE acitve edge
+p[2] =  24   # h_front_porch   = horizontal forward padding from DE acitve edge
-p[3] =  27   # h_sync_pulse    = hsync pulse width in pixel clocks
+p[3] =  80   # h_sync_pulse    = hsync pulse width in pixel clocks
-p[4] =  37   # h_back_porch    = vertical back padding from DE active edge
+p[4] =  104   # h_back_porch    = vertical back padding from DE active edge
-p[5] =  234   # v_active_lines  = vertical pixels height (lines)
+p[5] =  480   # v_active_lines  = vertical pixels height (lines)
 p[6] =  0   # v_sync_polarity = invert vsync polarity
-p[7] =  9   # v_front_porch   = vertical forward padding from DE active edge
+p[7] =  3   # v_front_porch   = vertical forward padding from DE active edge
-p[8] =  3   # v_sync_pulse    = vsync pulse width in pixel clocks
+p[8] =  10   # v_sync_pulse    = vsync pulse width in pixel clocks
-p[9] =  17   # v_back_porch    = vertical back padding from DE active edge
+p[9] =  7   # v_back_porch    = vertical back padding from DE active edge
 p[10] = 0   # v_sync_offset_a = leave at zero
 p[11] = 0   # v_sync_offset_b = leave at zero
 p[12] = 0   # pixel_rep       = leave at zero
 p[13] = 60   # frame_rate      = screen refresh rate in Hz
 p[14] = 0   # interlaced      = leave at zero
-p[15] = 5760000   # pixel_freq      = clock frequency (width*height*framerate)
+p[15] = 31500000   # pixel_freq      = clock frequency (width*height*framerate)
 p[16] = 1   # HDMI_ASPECT
 
 print("dpi_timings=", end='')